Source
Architecture, reliability & security assurance — found from sitemap — Appgate SDP
Checked for Appgate SDP on 10 Nov 2026
- Page
- https://support.appgate.com/docs/tunnel-architectures-v7-0
- Checked
- 10 Nov 2026, 12:02 UTC
- How we may use it
- Public page, crawling permitted
Technical details
- type
- page
- http status
- 200
- content hash
- sha256:cb8eaa4f88903e3a6964663fc34bd8307da51a9e1865b4b5c4df6de3139143fe
- permission
- robots_ok
- screenshot
- Screenshot on file (internal exhibit, not published)
Cited by
Facts read from this source
-
Multi site connections Report an error
“Unlike traditional VPN solutions, clients can connect to multiple Sites in a single Collective at the same time.”
-
Default site ebr Report an error
“New Collectives include a default Site preconfigured to use entitlement-based routing (EBR).”
-
Tunnel protocols Report an error
“AppGate ZTNA supports both TCP and UDP for the tunnel. This choice does not affect the protocols supported within the tunnel.”
-
Tunnel inner protocols Report an error
“The tunnel supports TCP, UDP, GRE, and ICMP, as well as inbound and outbound traffic.”
-
Tunnel mtu Report an error
“Tunnels use the default MTU of 1500 for the appliances' external NICs.”
-
Default tunnel mode Report an error
“The default tunnel mode is TLSv1.3. QUIC is also available for use cases that require it.”
-
Ios site limit Report an error
“On iOS and iPadOS, do not use more than five Sites. Exceeding five Sites is likely to exceed the memory limit for VPN services.”
-
Quic no handshake Report an error
“QUIC has no handshaking. It streams packets with no guarantee of packet delivery or retry on failure. This can improve performance on high-latency networks where low delay matters more than packet loss—for example, VoIP traffic.”
-
Spa quic mode Report an error
“To use single packet authorization (SPA) functionality on Gateways, use Check UDP (and TCP) SPA mode. In Check TCP SPA mode, SPA applies only to TLS-based connections such as the client-to-Controller connection. It has no effect on the QUIC tunnel to the Gateways.”
-
Sdp model Report an error
“Tunneled connections follow the software-defined perimeter (SDP) network model.”
-
Source nat default Report an error
“By default, Disable Source NAT on Gateways is not enabled, so Gateways perform source NAT”
-
External load balancer Report an error
“When you use an external load balancer, you cannot enable UDP-TCP SPA mode because the load balancer cannot handle both UDP and TCP traffic. Load balancers also lack an equivalent cloaking feature, making them visible on the internet.”
-
Load balancer layer limit Report an error
“Using TCP SPA mode with mTLS also limits your load-balancer options. These two security features protect against man-in-the-middle attacks, which makes application-layer load balancers unusable. The load balancer must operate exclusively at the DNS or TCP/IP layer.”
-
Load balancer healthcheck Report an error
“Configure the load balancer to use the Healthcheck Server to probe each appliance, so that clients are not directed to unavailable appliances.”
-
Built in ha recommended Report an error
“For both the Controller and Gateway, use the built-in HA mechanisms rather than an external load balancer. The built-in mechanisms are designed to optimize scalability, security, and performance.”
-
Connect via local network Report an error
“There is an optional setting for Connect via Local Network in the Gateway’s Secure Tunnel Settings, which allows the Gateway's Local Client Hostname/IP (172.17.111.10,11,12) to be added.”
-
Local lan no hairpin Report an error
“Clients access the Gateways on that Site directly, without hairpinning traffic through the firewall.”
-
Nearest site override Report an error
“AppGate ZTNA provides the Override with nearest Site option.”
-
Entitlement site assignment Report an error
“By default, entitlements are assigned to one Site only.”
-
Fallback site Report an error
“After a minimum of 30 seconds, the client determines that a Site is unresponsive and switches to the fallback Site.”
-
Fallback client controlled Report an error
“The client controls the fallback process, so an outage affecting the Controller Site does not prevent failover.”
-
Ip pool mapping Report an error
“The IP Pool mapping feature in Sites allocates a mapped IP address from the range 192.168.101.1–63 for use on the 112.x Site. The allocation option reduces the required IP pool size”
-
Ip pool translation Report an error
“The IP Pool mapping feature in Sites performs one-to-one translation of IP addresses (from 192.168.100.64–254 to 192.168.101.64–254) for use on the 112.x Site.”
-
Site definition Report an error
“Site is an AppGate ZTNA term for the environment that the system protects. Do not confuse it with a physical site. A Site may represent one or more hosts in a subnet, a DMZ, a geographic location, or a business unit.”
-
Entitlement home site Report an error
“Every entitlement you configure must relate to a default Site—that entitlement’s home.”
Scores citing this record
- The DevOps Engineer Access model & connectivity
- The DevOps Engineer Architecture, reliability & security assurance
- The DevOps Engineer European sovereignty
- The IT Lead Access model & connectivity
- The IT Lead Architecture, reliability & security assurance
- The IT Lead European sovereignty
- The MSP Technician Access model & connectivity
- The MSP Technician Architecture, reliability & security assurance
- The MSP Technician European sovereignty
- The Operations Manager Access model & connectivity
- The Operations Manager Architecture, reliability & security assurance
- The Information Security Officer Access model & connectivity
- The Information Security Officer Architecture, reliability & security assurance
- The Skeptic Access model & connectivity
- The Skeptic Architecture, reliability & security assurance